Vehicles
103 not categorized PORSCHE BOXSTER ETWCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.91163111502 This is the seal that sits between the adjustment ring and the outer headlight trim ring. Sold individually. Driver's and passenger's side fitment. 2 necessary per car. View/Change Diagram
From $5.00
Make a selection 91156509047 As our classics age, original gaskets and seals become brittle, crack and disintegrate. The windshield seal is essential to prevent moisture front entering between the roof and windshield. An old seal will also create more noise as disintegrates. This seal is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: this seal requires modification / trimming to fit. View/Change Diagram
From $251.21
Make a selection 914352423A This is the splined adjusting lug for the inside of the rear 914 caliper. it is easily removed by cocking a long 4mm allen wrench in it. it is located under the inner adjuster cover which may have an allen socket or a 10mm bolt head to remove. extra long for an easy reach. adjusted through the swing arm, the pads need to have 8 thousands clearance between the pad and the rotor, and check the rotor for warpage. General Fitment914 1970-76
$26.50
Make a selection 91450410510 Beautiful reproduction! perfect replacement for the long discontinued factory part, this fits in between the engine lid grill and the painted part of the engine lid acting as a buffer. easily installed, we include enough for all grilles as well. View/Change Diagram
$10.07
Make a selection 91453182210 The "b" part is an excellent reproduction of the original seal. The r and g are originals. this is the seal that fits on the unibody between the rocker carpet and the threshold, this assures a good door seal and no rattles! slightly smaller than the original, it is easily installed with a plastic hammer (or a strong heal of the hand!) order the corresponding seal on the door for the tightest fit. View/Change Diagram
From $37.10
Make a selection 91455901710 Drivers side finishing strip for the top of the roll bar in between the side and upper vinyl covering. View/Change Diagram
$35.79
Make a selection 91455940210RP Will ship when ready. General Fitment914 1970-76
$260.75
Make a selection 91473111610 Exellent reproduction for the fussy concours enthusiast who demands the best. fits between the outer mirror and the doorskin was factory original equipment until discontinued. our repro is excellent and made of high quality nylinized rubber for long life View/Change Diagram
From $4.80
Make a selection 90110821403 Gasket between stack base and main filter housing 2 per car View/Change Diagram
From $19.78
Make a selection 96437502301RATK Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.
$176.00
Make a selection 93011014103 This flange houses the fuel injector port. It sits between the intake manifold and the cylinder head. It suffers from an intense amount of heat and can develop cracks and damage. It is critical to replace once damage occurs. We also recommend replacing the gaskets, part # 93011019710 sold individually. 6 necessary per car. View/Change Diagram
From $40.95
Make a selection 93011015200
View/Change Diagram
From $13.20
Make a selection 95504480103 Group 2 + 3 seat for children from 33 - 80 lbs. / approx. 3,5 to 12 years of age. . Porsche child seats can be fitted into position quickly and securely using the standard north american latch fastening system in conjunction with the Porsche child seat fastener system which needs to be installed through your authorized Porsche dealer. Telescopic bars on the child seat lock into place between the backrest and the seat and hold it firmly to the passenger seat. Child seats may only be used in the Boxster, 911 or Cayman on the passenger seat in conjunction with the child seat fastener system. To avoid the risk of injury from a deploying airbag, never place a child age 12 or under in a front seating position without...(choose a part on the right to read more) General FitmentACCESSORY
$303.15
Make a selection 93010519306 Chain case gasket, each, two needed. View/Change Diagram
From $2.25
Make a selection 94410519903
View/Change Diagram
From $8.00
Make a selection 94460225700 This is the gasket that fits in between the distributor cap and the distributor base on all 944 models to seal out the water. an easy peel and stick installation. View/Change Diagram
$9.01
Make a selection 93021162201 Each hose sold seperately. These long-lasting aircraft quality heater hoses conduct only the hottest heat to the front of your Porsche, while providing flex during engine movement! Order 4 hose clamps as well! Fit under the car near the engine and connect between the heater control valve and the body. 60 x 330 mm View/Change Diagram
From $23.10
Make a selection 959SB Up to 1987, all 911 came with a long black metal stick shift between the seats, rising up from a rubber shift boot. Our 911 shift boot is a great way to cover up the shift and update it to a modern luxurious look. 1987 through 1989, Porsche changed the transmission to a better unit, called a “g-50”. The leather on these were very thin and wear out quickly, especially lighter colors such as linen and camel. Our replacement boots uses thicker leather to avoid this problem. Please indicate color and specify 4 or 5 speed emblem when ordering. This part has a 2-3 week lead time. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1970-73
$89.99
Make a selection 96410411107 If you are performing cylinder head work these seals are a necessary replacement. They are located between the valve spring and the valve guide. When these seals are failing, you will notice smoke from the tailpipe at startup. Sold individually. 12 necessary per car. Please note: this is the latest supersession part # for 928 104 193 12 and 928 104 193 13. Please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $1.50
Make a selection 96410628308 This cover sits upright along the back of the motor nearest the fire wall on the left side. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend replacing the grommet, part 91160640700 at the same time. Sold individually. 1 necessary per car. Please note: small modifications may be necessary between models View/Change Diagram
From $413.60
Make a selection 30301997K The jrz rs pro takes the jrz rs one step further by adding an external reservoir which makes this system very close to the race double adjustable damper. The jrz rs pro is a double adjustable monotube damper with remote reservoirs mounted on fixed high pressure hoses, or in piggyback setup for simple installation. General Fitment911 GT3 2007-11
$8,322.75
Make a selection 99611601534 Made in Germany by sachs to original specifications. Oem disc. 240 mm with torsion springs. Max torque: 313 lb/ft (425 nm) weighs: 4.4 lbs. (1.99 kg) discs with torsion springs function as a vibration damper between the engine and gearbox. They effectively lessen the harshness felt during re-engagement.
$518.10
Make a selection A1032 The girodisc system is a direct replacement for the oe disc with the addition of girodisc provided caliper spacers and longer bolts. Girodisc rotor is slightly larger than the OEM rotor at 350mm versus 330mm providing greater braking force and cooling capacity. General Fitment911 1998-05911 TURBO/GT2 2001-05 911 2005-08
$1,620.00
Make a selection A1103 The girodisc system is a direct replacement for the oe disc. No modifications are necessary. The disc will bolt directly to the car and work with oe calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your abs efficiency. General Fitment911 1989-94
$1,350.00
Make a selection A1122 The girodisc system is a direct replacement for the oe disc with the addition of girodisc provided caliper spacers. Girodisc rotor is slightly larger than the OEM rotor at 350mm versus 340mm providing greater braking force and cooling capacity. The girodisc front rotors are approx 21.0 lbs vs. 24.4 lbs for the stock units. This reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. General Fitment911 2009-12
$1,620.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |